In the installation of villa door often encounter some problems, today we Jinan copper door for you to prepare a set of villa door device guidance scheme, for your reference.

　　机:

　　Machine:

　　1.在安装门之前，要考虑门框和立面是否完好，是否有损坏，配件是否齐全。

　　1. Before installing the door, consider whether the door frame and facade are in good condition, whether there is damage, and whether the accessories are complete.

　　2.检查花边是否弯曲，如果有弯曲需要调整装置。

　　2. Check whether the lace is bent. If there is bending, adjust the device.

　　3.反映龙门的对角线，将误差调整到5毫米以内。

　　3. Reflect the diagonal of the gantry, and adjust the error to within 5mm.

　　4.反映门的大小是否必须与上、中、下不同，上、下、右侧面是否可以与空气平行，是否垂直90度，空气是否平坦。

　　4. Reflect whether the size of the door must be different from the top, middle and bottom, whether the top, bottom and right sides can be parallel to the air, whether they are 90 degrees vertical, and whether the air is flat.

　　安装门:

　　Install the door:

　　1.门框到门必须左派和右派垂直平行,如门框比一厘米大于门框必须使用石头或木头门框发挥缩小螺钉位置垫,在门框左右上角底部次发挥缩小螺丝不收紧。罗马柱的门首先要安装在门框后面进入门洞。

　　1. The door frame to the door must be vertical and parallel to the left and right sides. If the door frame is one centimeter larger than the door frame, the stone or wood door frame must be used to play the reducing screw position pad. The first time the reducing screw is played at the bottom of the left and right upper corners of the door frame, it will not be tightened. The Roman column door is first installed behind the door frame to enter the door opening.

　　2.挂facade,无论是反射表面和门框之间的差距可以并行,大小是否可以标准化,是否上面的门可以打开成一条直线的两个门面,两个主要的差距和副门不能大于5毫米,反射能否顺利打开和关闭。

　　2. Hang the facade, whether the gap between the reflecting surface and the door frame can be parallel, whether the size can be standardized, whether the upper door can be opened into two doors in a straight line, and whether the gap between the two main doors and the secondary door cannot be greater than 5mm, and whether the reflection can be opened and closed smoothly.

　　3.调整好后，取下外立面，再拧上其他螺丝。拧紧螺丝时，应将上下两侧依次反复拧紧。紧固螺钉应以门框为准，不得拉紧。

　　3. After adjustment, remove the facade and screw in other screws. When tightening the screws, the upper and lower sides shall be tightened repeatedly. The fastening screws shall be subject to the door frame and shall not be tightened.

　　4.将立面倒挂起来，重新检查缝隙和开口与闭合。如果有差异，尽量调整收缩螺丝的松紧度，调整门的间隙和开关门。

　　4. Hang the facade upside down and recheck the gap, opening and closing. If there is any difference, try to adjust the tightness of the shrinkage screw, adjust the gap of the door and the opening and closing of the door.

　　5.将手柄固定后固定在立面上，不要将手柄螺丝旋得太紧。

　　5. Fix the handle on the elevation after fixing it, and do not screw the handle screw too tightly.

　　6.设备完成后，只有在门调整完成后才能停止操作，将泡沫或水泥放入门框内。在使用过程中，门框不得因门框受力过大而变形。

　　6. after the device is completed, only after the door adjustment is completed can the operation be stopped and the foam or cement placed in the doorframe. During the use, the door frame shall not be deformed due to the excessive stress on the door frame.

　　以上是 济南铜门制造商为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：//www.doveish.comThe above is the relevant content introduced by Jinan copper door manufacturer. To learn more, please visit the website: //www.doveish.com